<rp id="n3lel"><samp id="n3lel"></samp></rp>
<ol id="n3lel"></ol>

    1. <tbody id="n3lel"><pre id="n3lel"></pre></tbody>
      <rp id="n3lel"><strike id="n3lel"><u id="n3lel"></u></strike></rp>
      <span id="n3lel"><pre id="n3lel"></pre></span>
    2. <rp id="n3lel"><samp id="n3lel"><bdo id="n3lel"></bdo></samp></rp>
      <ol id="n3lel"></ol>

       

      Diaphragm Glossary & Design Formulas

       

      Hardware

      Convolution Width

      The clearance between the cylinder wall and piston skirt. By decreasing the convolution width, higher working pressures may be achieved. Generally, the convolution width should measure at least four times the diaphragm's sidewall thickness.

       

      Diaphragm convolution

      Cylinder Diameter (Bore)

      The inside diameter of the cylinder into which the diaphragm will fit and by which the outside diameter of the convolution will be supported.

      Cylinder Radius

      The blend radius between the cylinder wall and the flange.

      Piston Cap

      A plate which attaches to the piston, sandwiching the piston area of the diaphragm insuring the diaphragm stays in convolution.

      Piston Diameter

      Diameter of the piston measured across piston head, including radius.

      Piston Radius

      The blending radius between the piston head and the piston skirt.

      Piston Skirt

      The sidewall area of the piston which supports the inside diameter of the convolution.

      Diaphragm

      Cylinder Diameter

      The diameter across the diaphragm between the tangent points of the sidewall and cylinder radius.

       

      Diagram Top Hat with Cylinder Diameter
      Preconvoluted Diaphragm

      Fabric Side

      Surface of single coat diaphragm where fabric is visible. Always on low pressure side, generally on outside of diaphragm.

      Height

      The height of top hat and preconvoluted diaphragm is measured from the bottom of the flange to the top of the head or convolution.

      Piston Diameter

      The diameter across the diaphragm between the tangent points of the sidewall and piston radius. Measured on the fabric or low pressure side of the diaphragm.

      Preconvoluted

      A diaphragm which has its convolution molded in. No hand forming is necessary before installation.

      Sidewall

      That area of the diaphragm between the flange and piston areas.

      Top Hat

      A diaphragm molded in standard "hat" shape that must be formed into convolution before installation.

      Function

      Bleedthrough

      A defect in a diaphragm caused during manufacturing where the fabric is pulled through the rubber to the high pressure side of the diaphragm. When pressure is put on the diaphragm, the rubber will be blown away from the fabric and rupture.

      Blowthrough

      This occurs when the pressure on the diaphragm reaches a level high enough to blow a piece of the rubber through the threads of the fabric, causing a leak. This is the result of selecting a weave of fabric that is too open for the diaphragm's thickness.

      Double Coat

      This is a type of diaphragm construction where the fabric is inserted between two layers of rubber.

      Effective Pressure Area

      The area of the diaphragm inside an imaginary circle to the convolution midpoint on which the pressure introduced is transmitted to the opposite side of the diaphragm.

      Overstroke

      Exceeding the designed stroke of the diaphragm, causing it to come out of convolution. This can be avoided by designing mechanical stops into your hardware.

      Reverse Pressure

      When the pressure on the low pressure side of the diaphragm exceeds the pressure on the high pressure side of the diaphragm. This will cause the convolution to collapse and wrinkle. This wrinkle will cause scrubbing and lead to premature failure.

      Single Coat

      This is a type of diaphragm construction where there is rubber in the high pressure side and fabric on the low presure side.

      Spring Rate

      This refers to the forces caused by the rubber trying to return to its as-molded position. This is generally found only in preconvoluted and dish-shaped diaphragms.

      Strikethrough

      This refers to the amount of rubber that comes through the fabric to either fully or partially encapsulate the fabric during manufacturing.

      Diaphragm Design Formulas

      Diaphragm Design Formulas

       

       

       
      Inches
      mm
      Inches
      mm
      Inches
      mm
      Inches
      mm
      Cylinder Diameter
      .33-
      .99
      8.38-
      25.15
      1.00-
      2.50
      25.40-
      63.50
      2.51-
      4.00
      63.75-
      101.60
      4.01-
      8.00
      101.85-
      203.20
      *Safety Factor
      .060
      1.52
      .100
      2.54
      .120
      3.05
      .140
      3.56

      Diaphragm Strokes

      Diaphragm Strokes

       

       

       

       

      Have Questions?

      Notice: Undefined index: submit in /data/home/qxu1885270140/htdocs/contact-form.php on line 38








       

       

       

       

      <rp id="n3lel"><samp id="n3lel"></samp></rp>
      <ol id="n3lel"></ol>

      1. <tbody id="n3lel"><pre id="n3lel"></pre></tbody>
        <rp id="n3lel"><strike id="n3lel"><u id="n3lel"></u></strike></rp>
        <span id="n3lel"><pre id="n3lel"></pre></span>
      2. <rp id="n3lel"><samp id="n3lel"><bdo id="n3lel"></bdo></samp></rp>
        <ol id="n3lel"></ol>
        日本成年片在线观看_免费观看日本污污ww网站_67194中文乱码一二三四芒果_少妇色欲网